"브레드보드"는 한국어-영어 방향으로 TREX에서 찾을 수 없습니다.
영어-한국어 검색 해보십시오
(
브레드보드)
You need a breadboard, and then some wires.이제 다음과 같이 브레드보드의 작은 구멍에 LED를 꽂습니다.
Now place the LEDs into the small holes in the breadboard like this.LCD 디스플레이와 센서를 동일한 브레드보드에 모두 설정할 수 있습니다.
Could you set up both the LCD display and the sensor on the same breadboard.그리고 하나 브레드보드, 땜 납, 납땜 또는.
and one Breadboard, or solder and a soldering iron.아직도, 아무도는 그것의 브레드보드 표시에서 회로를 이해 해야 한다; 정말 어렵다.
Still, nobody should have to understand a circuit from its breadboard representation; it's really hard.
in the following diagram, Although it is much better to use a Breadboard;Arduino Yun Mini는 최대 400MHz에서 작동하는 ATmega 32u4 MCU와 QCA MIPS 24K SoC CPU로 개발된 브레드보드 PCB입니다.
Arduino Yun Mini is a breadboard PCB developed with ATmega 32u4 MCU and QCA MIPS 24K SoC CPU operating up to 400 MHz.Arduino의 핀은 전선을 연결하여 회로를 구성하는 곳입니다(아마도 브레드보드와 일부 와이어를 결합할 수 있습니다.
The pins on your Arduino are the places where you connect wires to construct a circuit probably in conjuction with abreadboard and some wire.사이 연결에 브레드보드 그리고는 라즈베리 그들은 다음 다이어그램에서와 같이 해야 합니다.,
The connections between the Breadboard and the Raspberry they must be as in the following diagram, the GPIO You can reach그러나 당신이 브레드보드 배치의 도표를 필요로 하는 경우에, 나는 아무것도를 잘 본.
if you need a graphic of a breadboard layout, I haven't seen anything better.다른 행과 가로로 연결되어 있습니다. 남아 있는 구멍들은 다섯 개의 구멍이 있는 열과 세로로 연결되어 있으며, 브레드보드의 가운데에 있는 가로 구멍은.
The remaining holes are connected vertically in columns of five holes. and there is no link across the horizontal gap in the middle of the breadboard.
and one Breadboard.난 하나를 사용 하려고 해요 브레드보드, 내가 사용 하는 것이 좋습니다는,
I'm going to use one Breadboard, and I recommend that you use a, There are some from approximately €4
This is a breadboard.브레드보드 안에는 많은 부품이 들어 있습니다.
Hidden inside the breadboard are many components.브레드보드를 사용하면 임시 프로토타입을 만들고 다양한 회로 설계를 실험할 수 있습니다.
Using a breadboard allows you to create temporary prototypes and experiment with different circuit designs.이제 브레드보드에 회로를 만드는 것을 완료했으므로, 우리는 이제 각 철사가 어느 핀에 연결될 것인지에 대해 고민해보아야 합니다.
Now that we have finished making a circuit in our breadboard, we need to think about which pins these wires are connected to on the Arduino.그러나, 브레드보드 시제품 기술은 광대역 무선 주파수(RF) 회로처럼 어떤 특별한 응용이나, 부품의 소프트웨어 방법이 부정확하거나 완벽하지 않은 곳에 여전히 사용된다.
However, prototyping techniques are still used for some applications such as RF circuits, or where software models of components are inexact or incomplete.
English
عربى
Български
বাংলা
Český
Dansk
Deutsch
Ελληνικά
Español
Suomi
Français
עִברִית
हिंदी
Hrvatski
Magyar
Bahasa indonesia
Italiano
日本語
Қазақ
മലയാളം
मराठी
Bahasa malay
Nederlands
Norsk
Polski
Português
Română
Русский
Slovenský
Slovenski
Српски
Svenska
தமிழ்
తెలుగు
ไทย
Tagalog
Turkce
Українська
اردو
Tiếng việt
中文