"Naar de controller" is not found on TREX in Dutch-English direction
Try Searching In English-Dutch
(
Naar de controller)
Door middel van analoge I/O modules kunnen deze signalen op een digitale manier naar de controller gebracht worden via de standaard AS-i kabel.
By means of the analogue I/O modules these values can then be digitally transmitted to the controller via the standard AS-i cable.Kan gebruikt worden als toevoerbus voor hoger gelegen bussystemen die op hun beurt een niet-tijdkritische transmissie van data naar de controller over lange afstand verzorgen.
It can be used as a feeder bus for higher bus systems, they in turn then ensure a non time critical transmission of the data over longer distances to the host controller.Command[Pw R2 off R4 0 R2 on R4 144 s] zijn alle geldig. Meervoudige opdrachten zijn dus ondersteund in hetzelfde SMS-bericht naar de controller.
Multiple commands are supported in the same SMS command to the controller; Pw R3 on R2 0 R1 on 555 R4 1220 s.commando wordt automatisch verzonden naar de controller via de WiFi/ LAN
command is automatically sent to the controller via the WiFi/ LANde command[0000 i off] te verzenden vanaf het internet of SMS naar de controller.
must be sent from the internet or SMS to the controller.Steek de ene kant naar de controller en de andere op uw pc seriële
Plug one side to the controller and the other to your PC serialGet Your Controller Klaar Om uw Android-telefoon of tablet naar de controller genoemd als mogelijk Bluetooth-verbinding te bekijken,
Get Your Controller Ready In order for your Android phone or tablet to view the controller listed as a possible Bluetooth connection,Telkens wanneer de accountgegevens worden ingevoerd zullen ze automatisch worden verzonden naar de controllers.
Whenever the account credentials are entered they will be automatically sent to the controllers.die u toestaat om opdrachten te verzenden naar de controllers en maakt het mogelijk toestemming voor eHouse Home Automation systeem.
which allows you to send commands to the controllers and allows authorization to eHouse Home Automation system.natuurlijk gaat het direct naar de controllers aan de top. Wel, wat is nieuw.
of course it's going right to the controllers at the top(well, what's new?), but well worth seeing.maak alle kabels los die van de controller naar de FD drives lopen.
take off the cable that goes from the FD controller to the FD drives.De[AT+] mode herstelt het versturen van SMS-berichten vanaf de controller naar de mobiele telefoon in plaats van op het scherm.
The[AT+] mode makes send controller SMS messages to your mobile instead of on the screen.Data wordt dan door de controller naar de disk gestuurd die de gebruiker aangeeft,
Data is send by the controller to the disk you specify directlyNB:(1) Als de stroomtoevoer naar de SmartPilot controller ingeschakeld wordt,
Notes:(1) Each time power to the SmartPilot controller is switched on,We kunnen nu al werking onze module zoemer door het aansluiten van de batterij naar de vlucht controller;
We can already now check operation our module buzzer by connecting the battery to the flight controller;Als de stroomtoevoer naar de SmartPilot controller ingeschakeld is, kunt u de disp toets gebruiken om het instrument als volgt uit
When power is applied to the Pilot Controller, you can use the disp button to switch it offHoog niveau van diagnostiek en de mogelijkheid om van de niveaudetectiesensor om continu te communiceren direct naar de safety controller ondersteunt SIL3 1oo1 veiligheidssysteem implementaties.
High coverage diagnostics and the ability to continuously communicate point level sensor directly to the safety controller supporting SIL3 1oo1 safety system implementations.Aan en uit zetten Als de stroomtoevoer naar de SmartPilot controller ingeschakeld is, kunt u de disp toets gebruiken om het instrument als volgt uit
All the time that power is applied to the SmartPilot controller, you can use the disp button to switch the instrument offDe monitor voor de taskuitvoeringstijd kan met de simulator worden gebruikt om uitvoeringstijden weer te geven voordat gegevens naar de fysieke controller worden gedownload.
The Task Execution Time Monitor can be used with the Simulator to display execution times before downloading to the physical controller.Noot: u moet de key en het certificaat naar de andere controller in een redundant systeem kopiëren,
Note that you must copy the key and certificate to the other controller in a redundant system,
Nederlands
Deutsch
Español
Français
عربى
Български
বাংলা
Český
Dansk
Ελληνικά
Suomi
עִברִית
हिंदी
Hrvatski
Magyar
Bahasa indonesia
Italiano
日本語
Қазақ
한국어
മലയാളം
मराठी
Bahasa malay
Norsk
Polski
Português
Română
Русский
Slovenský
Slovenski
Српски
Svenska
தமிழ்
తెలుగు
ไทย
Tagalog
Turkce
Українська
اردو
Tiếng việt
中文