壁厚 - 翻译成英语

• wall thickness
• wall thicknesses
• wall thick

在 中文 中使用 壁厚 的示例及其翻译为 英语

软管的壁厚只有2mm，气道短而直，气压损失小；.
The wall thickness of the hose is only 2mm, the airway is short and straight, and the air pressure loss is small.

管状型壁厚等于或大于50毫米且内径等于或大于270毫米。
Tubular forms with a wall thickness equal to or less than 50 mm and having an inner diameter equal to or greater than 270 mm.

但是，钢材的壁厚可以增加，稳定性高，支撑力强，抗风能力高达36公里/秒，抗震能力在8.8以上。
The wall thickness of steel materials can be increased, high stability, strong support, wind resistance up to 36km/ s, earthquake 8.8 above.

墙壁厚，枝叶繁茂彼此分离的别墅和别墅都慷慨地传播。
Walls of thick, lush foliage separate the villas from one another and the villas are generously spread out.

壁厚约为传统结构的1/2，内部使用面积增加。
The wall thickness is about 1/2 of the conventional structure and the internal use area is increased.

曝气软管的壁厚只有2mm，气道短而直，气压损失小。
The wall thickness of the hose is only 2mm, the airway is short and straight, and the air pressure loss is small.

这种高强度材料是可在各种壁厚，可以用各种机械接头的安装。
This high-strength material is available in a variety of wall thicknesses that can be installed with a variety of mechanical joints.

薄壁”通常是由壁厚少于1mm的轻便电子制件所定义的。
Thin wall' is usually defined by lightweight electronic parts with a wall thickness of less than 1 mm.

在这一阶段，影响壁厚分布的主要工艺参数有：预吹压力、预吹时间。
At this stage, the main process parameters affecting the wall thickness distribution are pre-blowing pressure and pre-blowing time.

表中未列出壁厚的重量，可取与之相近的两个重量计算平均值；.
The table does not list the weight of the wall thickness, preferably with the similar two weight calculation of the average;

壁厚约为传统结构的1/2，内部使用面积增大。
The wall thickness is about 1/2 of the conventional structure and the internal use area is increased.

无缝管可以承受高压，当然其壁厚也会随之增加，这需要根据压力要求来进行设计。
Seamless pipe can withstand high pressure, of course, the wall thickness will also increase pressure requirements that need to be designed.

外面零下42℃，但在10厘米壁厚集装箱内放置的植物容器里，西红柿在顽强生长。
The outside is minus 42° C, but in a plant container placed in a 10 cm thick container, the tomatoes are growing stubbornly.

主要的压力参数是2/T，S是屈服强度，T是壁厚。
The pressure parameters are mainly 2ST/T, S is the yield strength, and T is the wall thickness.

该设计有助于均匀地分布作用力，降低局部应力，意味着材料壁厚较薄，进一步实现材料减重及成本压缩。
This uniformly distributes the forces and reduces local stresses, meaning thinner wall materials, further reducing material weight and cost.

应用情况由于双相钢强度高，它往往可以节约材料，如减少管子的壁厚。
Due to the high strength of duplex steel, it can often save material, such as reducing the wall thickness of the duplex pipe.

不管是模塑成型还是传递成型，主要用来生产体积较大、壁厚较厚的产品。
Whether molded or transmissible, it is mainly used to produce products with larger volume and thicker wall.

降低最大允许工作压力或最大工作压力，但不影响壁厚；.
(h) A decrease of the maximum allowable working pressure, or maximum working pressure, not affecting thickness;

说明：上述系统用的专门设计的软件包括用于同时测量壁厚和轮廓的软件。
Specially designed software for these systems includes software for simultaneous measurements of wall thickness and contour.

术语“阻塞”用于测量挤压量。它要么表示为壁厚的两倍，要么表示为被压缩的壁的绝对量。
The term"occlusion" is used to measure the amount of squeeze. It is either expressed as a percentage of twice the wall thickness, or as an absolute amount of the wall that is squeezed.