注射压力 - 翻译成英语

injection pressure
注射 压力
喷射 压力
注塑 压力
注入 压力

在 中文 中使用 注射压力 的示例及其翻译为 英语

{-}
  • Political category close
  • Ecclesiastic category close
  • Programming category close
要增加熔体的流动性,不是用增大注射压力而应采用提高注射温度的办法来达到;
To increase the fluidity of the melt, it is not necessary to increase the injection pressure but to increase the injection temperature.
大浇口、厚壁短流程、小面积的制品,注射压力为40~80MPa;.
For large gates, thick-walled short-flow processes, and small-area products, the injection pressure is 40-80 MPa;
这是需要注射工程师根据产品的综合因素来合理界定注射压力控制的。
This requires the injection engineer to reasonably define the injection pressure control based on the combined factors of the product.
大浇口、形状简单及厚壁制品,注射压力可选低些,约60~80MPa。
Large gates, simple shapes and thick-walled products, the injection pressure can be lower, about 60~ 80MPa.
例如,提高树脂温度,模具温度的升高,提高注射压力和速度。
For example, increase the temperature of the resin, increase the mold temperature, and increase the injection pressure and speed.
根据经验,初步设定塑化量、注射压力的限定值、注射速度、冷却时间以及螺杆转速等参数,并对其进行适当的优化。
Based on experience, preliminarily set the amount of plasticizing, injection pressure limit, injection speed, cooling time and screw speed and other parameters, and appropriate optimization.
全球汽车零部件供应商电装公司开发了一种新的柴油共轨(DCR)燃油喷射系统2500条世界上海拔最高*注射压力
Global automotive supplier DENSO Corporation has developed a new diesel common rail(DCR) fuel injection system with the world's highest* injection pressure of 2,500 bar.
注射压力过高。
(1) injection pressure is too large.
注射压力:可大到1800bar。
Injection pressure can be as high as 1800 bar.
注射压力:可大到1800bar。
Injection pressure: up to 1800 bar.
注射压力:可大到1800bar。
Injection pressure: up to 1800 bar.
注射压力:可大到1500bar。
Injection pressure: up to 1500bar.
选用较高的注射压力和注射速度。
Higher injection pressure and injection speed are required.
一般来说,要求较高的注射压力与注射速度。
Generally speaking, higher injection pressure and injection speed are required.
注射压力:一般在750~1250bar之间(取决于材料和产品设计)。
Injection Pressure: Usually between 750 and 1250 bars(dependent on material and product design).
注射压力:一般在750~1250bar之间(取决于材料和产品设计)。
Injection pressure: generally between 750~ 1250bar(depending on material and product design).
它常用的注射压力从数千到数万kPa,甚至高达2×105kPa。
Its common injection specific pressure is from a few thousand to tens of thousands of kPa, and even up to 2 x 105 kPa.
也就是说,存在一个注射时间,此时所需的注射压力最小。
That is, there is an injection time at which the required injection pressure is minimal.
也就是说,存在一个注射时间,此时所需的注射压力最小。
In other words, there exists an injection time when the injection pressure required is minimal.
也就是说,存在一个注射时间,此时所需的注射压力最小。
That is to say, there is an injection time, and the injection pressure is small at this time.
结果: 98, 时间: 0.02

单词翻译

顶级字典查询

中文 - 英语