屈服强度 in English translation

• yield strength

Examples of using 屈服强度 in Chinese and their translations into English

C．如何使材料有足够的抗拉强度和屈服强度；.
How to make the material have sufficient tensile strength and yield strength;

相对于增强材料的屈服强度，其拉伸强度优选是屈服强度的约150％。
The tensile strength of the dispersed phase material with respect to its yield strength is preferably about 150% of the yield strength..

最终目标是生产出在高温仍然能保持大部分屈服强度的钢。
The ultimate goal is to produce steel that retains majority of its yield strength at high temperatures.

对于有明确屈服点的金属，对应于保证屈服强度，安全系数取1.5；.
(a) for metals having a clearly defined yield point, a safety factor of 1.5 in relation to the guaranteed yield strength; or.

(a)有明确屈服点的钢，对应于保证屈服强度，安全系数取1.5；或.
(a) for steels having a clearly defined yield point, a safety factor of 1.5 in relation to the guaranteed yield strength; or.

它具有良好的可拉伸性-低屈服强度和高伸长率的组合允许制造成复杂的形状。
It has good drawability- the combination of low yield strength and high elongation permits fabrication into complex shapes.

BSEN10149-1-1996冷成型用高屈服强度钢制热轧扁平产品.第1部分:一般交货条件.
DIN EN 10149-1- Hot rolled flat products made of high yield strength steels for cold forming- Part 1: General technical delivery conditions.

抗压强度、屈服强度、极限强度、弹性极限和弹性模量等参数也是通过测试材料来确定的。
The parameters like compressive strength, yield strength, ultimate strength, elastic limit, and elastic modulus are also determined by testing a material.

(d)制造材料标准的改变，条件是允许屈服强度达到或超过试验的便携式罐体；.
(d) A change to the grade of material of construction provided that the permitted yield strength meets or exceeds that of the tested portable tank;

现在，它被认为是300系列不锈钢的经济有效的替代品，可以提供提高屈服强度的额外好处。
It is now considered a cost-effective substitute for 300 series stainless steels that can provide an additional benefit of improved yield strength.

抗拉强度接近于屈服强度,比ABS高一倍多。
Tensile strength close to the yield strength, more than double the ABS.

屈服强度是通过0.2%抵消方法得到的。
The yield strength was characterized by the 0.2 percent offset method.

拉伸强度接近屈服强度，是ABS的两倍以上。
Tensile strength close to the yield strength, more than double the ABS.

这种钢的屈服强度也很高。
The yield strength of this steel is also very high.

抗拉强度接近屈服强度，是ABS的两倍多。
Tensile strength close to the yield strength, more than double the ABS.

HSLA-115钢的屈服强度约为800MPa，比HSLA-100钢（屈服强度约为690MPa）要高。
The yield strength of HSLA-115 steel is about MPA, which is higher than HSLA-100 steel(yielding strength is about 690 MPa).

它们通常是含碳量在0.05%～0.20%之间的铁-碳和为提高屈服强度及韧性而加入的其它少量合金元素的合金。
They are typically iron-carbons containing between 0.05% and 0.20% carbon and alloys of other small alloying elements added to improve yield strength and toughness.

进行应变测量时，例如测量与屈服强度对应的应变时，我们通常建议采用2630系列轴向夹式引伸计。
When performing strain measurements, such as the strain corresponding to the yield strength, we typically recommend our 2630 series of axial clip-on extensometers.

Q表示屈服强度，345表示这种钢材的屈服强度为345MPa。
Q represents the yield strength, and 345 indicates that the yield strength of the steel is 345 MPa.

当前国外变形镁合金的室温屈服强度最高达到300MPa，延伸率达到5%。
At present, the yield strength of deformation magnesium alloys in foreign countries reaches up to 300 MPa at room temperature and the elongation rate reaches 5%.