COLD JUNCTION in Chinese translation

• 冷端
• 冷结
• 冷接点

Examples of using Cold junction in English and their translations into Chinese

As an extra option, the ADT7311 digital temperature sensor can be used to measure the cold junction temperature instead of the RTD.
作为额外选项，ADT7311数字温度传感器可用于代替RTD来测量冷结温度。

Instead of using an external RTD, the ADT7311 temperature sensor can be used to measure the cold junction temperature.
作为额外选项，ADT7311数字温度传感器可用于代替RTD来测量冷结温度。

Figure 2 shows that the cold junction temperature is measured with another temperature sensitive device, typically a thermistor, diode, RTD, or semiconductor temperature sensor.
图2显示，冷端温度使用另一种温度敏感器件来测量，其通常是热敏电阻、二极管、RTD或半导体温度传感器。

We use the terms"measurement junction" and"reference junction" rather than the more traditional"hot junction" and"cold junction.".
我们使用术语"测量接合点"和"参考接合点"而不是更传统的"热接合点"和"冷接合点"。

The joined the other end of these dissimilar metals is referred to as the COLD END or COLD JUNCTION.
这些不同的金属的另一端被称为冷端或冷端。

The other end of these dissimilar metals is referred to as the COLD END or COLD JUNCTION.
这些不同的金属的另一端被称为冷端或冷端。

To maintain a consistent and known temperature of 0°C, traditional cold junctions would be chilled in an ice-cold water bath(hence the name"cold junction").
为了保持一致且已知的0°C温度，传统的冷端将在冰冷的水浴中冷却（因此称为“冷端”）。

Understanding of cold junction compensation is important;
了解冷端补偿很重要;

The RTD was used for cold junction compensation.
该RTD用于冷端补偿。

The RTD is used for cold junction compensation.
该RTD用于冷端补偿。

Also, Thermocouples need a reference measurement point called“Cold Junction”.
此外，热电偶需要一个称为“冷端”的参考测量点。

This process is known as reference junction compensation(cold junction compensation.).
此过程称为参考结补偿（冷端补偿）。

Compensation for the cold junction is made through an internal temperature measurement at the terminals.
通过终端处的内部温度测量进行冷接点补偿。

Hence, the voltage from a known cold junction can be simulated, and the appropriate correction applied.
因此，可以模拟来自已知冷结的电压，并应用适当的校正。

To make accurate measurements, this must be compensated for by using a technique known as cold junction compensation(CJC).
为了实现精确测量，需要应用一种技术手段，我们可以称之为冷端补偿(CJC)。

Traditionally this was done with a carefully constructed ice bath(hence the term‘cold' junction compensation).
传统上，这是通过精心构造的冰浴完成的（因此称为“冷”结合补偿）。

Therefore, other correction methods need to be used to compensate for the temperature influence when the cold junction temperature t0≠ 0℃.
因而，还需选用其他批改方法来补偿冷端温度t0≠0℃时对测温的影响。

The thermistor can also be used as an electronic circuit component for meter line temperature compensation and temperature difference cold junction temperature compensation.
热敏电阻也可作为电子线路元件用于仪表线路温度补偿和温差电偶冷端温度补偿等。

If the leads are too long or too thin, the total series resistance may cause signal degradation before the EMF reaches the cold junction.
如果引线太长或太薄，则总串联电阻可能在EMF到达冷端之前导致信号劣化。

The joined end is typically referred to as the“hot” junction, while the open end is called the“cold” junction.
接合在一起的这端通常叫做“热”端，而开口的那一端叫做“冷”端。