CUTTING SPEED in Chinese translation

• 切割速度
• 切削速度

Examples of using Cutting speed in English and their translations into Chinese

When the focus is in the right position, small slot, high efficiency, cutting speed can get good cutting results.
当聚焦在合适的位置时，狭缝小，效率高，切削速度快，可获得良好的切削效果。

Accordingly, they retrofitted their CNC vertical machining center(VMC) with an air spindle capable of 175,000 rpm, but cutting speed was not enough.
于是，他们着手对带转速高达175000r/min的空气主轴的CNC立式加工中心(VMC)进行了改装，但是切割速度还是不够。

On high-speed machines, 2205 alloy feed rate and cutting speed and 316L is the same.
在高速的机床上,2205合金的进给率和切削速度和316L是一样的。

With HYPERTRON®, you can reach a 30 to 50% higher cutting speed and energy efficiency combining servo technology with ultra-high pressure.
使用HYPERTRON®，将伺服技术和超高压相结合，您可增加30-50%的切割速度和能效。

When the focus is in the right position, small slot, high efficiency, cutting speed can get good cutting results.
当焦点在正确的位置时，开槽小，效率高，切削速度能得到良好的切削效果。

To achieve perfect stock removal results, we recommend a cutting speed of 12- 15 m/s and the use of a hard contact wheel.
为了获得最佳的磨削效果，推荐使用12-15米/秒的切割速度和较硬的接触磨片。

It uses a cutting speed that is twice the speed of conventional hobbing and can reach 200m/min.
它采用的切削速度是传统滚切速度的）倍，可达到200m/min。

This time we increased the cutting speed a bit, from 350 to 400 sfm, and bumped up the feedrates by about 30 percent.
我们这次将切削速度略微提高了一点，从350sfm到400sfm，进给率则猛增了约30%。

When cutting plastic metal, when the cutting speed is very low or high, the surface roughness value is small.
切削塑性金属时，当切削速度很低或很高时，表面粗糙度值较小。

The cutting speed necessary for successful hard milling with ceramics is based on the actual material hardness, usually in the 45- 65 Rockwell C hardness range.
用陶瓷刀片成功实现硬铣削所需的切削速度基于实际的材料硬度（通常在45～65HRC范围内）。

This time we increased the cutting speed a bit, from 350 to 400sfm, and bumped up the feedrates by about 30%.
我们这次将切削速度略微提高了一点，从350sfm到400sfm，进给率则猛增了约30%。

In another case, in the same period, the cutting speed of ISCA ic50m milling martensitic Stainless steel was 80m/m i n;
在另一案例中，相同时期，采用伊斯卡非涂层牌号IC50M铣削马氏体不锈钢的切削速度为80m/min；.

From the processing example, 30 years ago, the cutting speed of the ISCA non-coated cemented carbide grade IC20 turning gray Iron was about 100m/mi N;
从加工实例来看，30年前，采用伊斯卡非涂层硬质合金牌号IC20车削灰铸铁的切削速度大约为100m/min；.

Now, the cutting speed of ISCA coated cemented carbide grade IC5005 is 600m/min.
现在，采用伊斯卡涂层硬质合金牌号IC5005的切削速度达600m/min。

The company will exhibit energy-efficient, high-performance band-sawing machines with a very high cutting speed at AMB 2014.
该公司将在AMB2014展会上展示具有非常高的切削速度的节能、高性能带锯床。

In gas cutting specifically, the oxygen must be of high quality to ensure a high cutting speed and a clean cut..
在气割，氧气必须是高质量的，以保证较高的切削速度和一个干净的切割。

Then, attempting to speed output and productivity, the shop increases cutting speed by 10 percent.
然后，为了提升产量和生产率，车间将切削速度提高10%。

In 1868, the British RFMushet invented an ingredient of 2.5% Mn. -7% W self-hardening steel, increasing cutting speed to 5 m/ min.
年英国人马希特(R.F.Mushet)发明了成分为2.5%Mn-7%W的自硬钢，将切削速度提高到5米/分。

Similarly, the gas flow, arc length, telegraph quality, current size, cutting speed are affecting the quality, not well conceived, not as simple as flame cutting..
同样，气体流量、电弧长度、电报质量、电流大小、切割速度都影响质量，掌握不好也不埋想，不如火焰切割简单。

The machine, called Slimbox, cuts the carton into the desired shape according to the user's settings and automatically controls the cutting speed for best results.
这台机器名为Slimbox，其能按照用户的设置，将纸箱裁成理想的形状，并自动控制切割速度、达到最佳效果。