Examples of using Nozzle in English and their translations into Chinese
{-}
-
Political
-
Ecclesiastic
-
Programming
Typical objects in this category are fasteners, yaw and yo-yo weights, nozzle covers, lens caps, multiple payload mechanisms and so forth.
该类中的典型物体是系固件、方向舵和游游重物、喷管堵盖、透镜罩、多有效载荷机械装置等。Marc Laan, Product Manager VEX/Fire adds:“The‘click and seal' design is a major breakthrough in the nozzle market.
VEX/消防部产品经理马克.朗恩补充说：“‘咔哒密封'设计是管口市场的一个重大突破。You need the ink to flow out of a nozzle like toothpaste, and it can maintain its shape after it's printed.
For example, when you print, you suddenly hit your printer, and you may cause the nozzle to move to a new location.
例如，在打印的时候，你突然撞击你的打印机，你可能导致喷头移动到一个新的位置。(Unless the shape is complex and thin-walled parts require a higher injection speed), the product nozzle position is prone to gas lines.
除非形状复杂、薄壁制件需用较高的注射速度），产品水口位易产生气纹。Generated by air flow at the nozzle outlet low pressure to draw air or other gases, and then discharged to compress it.
靠气流在喷嘴出口处产生低压来抽吸空气或其他气体，然后把它压缩排出。To stabilize the engine speed and spray pressure to ensure that the nozzle is well atomized and to ensure uniform spraying.
以稳定发动机转速和喷雾压力，以确保喷头雾化良好和保证均匀的喷洒。The nozzle helps reduce the flow from 8 litres to 3 litres a minute,” said Pradeep Surana, another resident.
喷嘴有助于减少从8升到3升的流量一分钟，”PradeepSurana说，另一位居民。Inferior consumables will not only affect the quality of printing, serious and even lead to the damage of painting equipment and nozzle.
劣质耗材不但会影响到打印质量，严重时甚至会导致喷绘设备和喷头的损坏。(3) Pipe support, the installation position of the hanger should not hinder the water spray effect of the nozzle;
管道支架、吊架的安装位置不应妨碍喷头的喷水效果；.Until now, 3D-printed battery efforts were limited to extrusion-based printing, where a wire of material is extruded from a nozzle, creating continuous structures.
到目前为止，3D打印电池的工作仅限于基于挤出的打印，其中材料线从喷嘴挤出，形成连续的结构。And within the limits of the rails, the arm will build the house layer by layer by extruding concrete from the nozzle.
并且在轨道的限制范围内，臂将通过从喷嘴挤出混凝土逐层构建房屋。Also, the extruder needs to be at correct height from the bed and the nozzle is at the right distance from the bed.
而且，挤出机需要位于距离床的正确高度处，并且喷嘴与床的距离正确。This bubble expands at a very fast rate(less than 10 microseconds), forcing ink droplets to eject from the nozzle.
这个汽泡以极快的速度(小于10微秒)扩展开来，迫使墨滴从喷嘴喷出。For example, an atomizer wheel will give you a wider distribution of particle size while a nozzle will give you narrower distribution.
例如，雾化器轮将为您提供更宽的粒度分布，而喷嘴将为您提供更窄的分布。After the 3D file, the printer now heats the material and squeezes it through the nozzle while moving, one layer at a time.
在3D文件之后，打印机现在加热材料并在移动时通过喷嘴挤出，一次一层。Using 3D printing, GE dramatically improved the way it manufactures its fuel nozzle injectors for its best-selling LEAP jet engine.
通过使用3D打印，GE大幅改进了其制造最畅销的LEAP喷气发动机燃油喷嘴的方式。The bubble expands at a very fast speed(less than 10 microseconds), forcing ink droplets to eject from the nozzle.
气泡以非常快的速度（小于10微秒）膨胀，迫使墨滴从喷嘴喷出。Ultimately, microspheres range in diameter from 0.04 mm to 0.07 mm and easily pass through a standard 1.7 mm printer nozzle.
最终，微球体的直径范围为0.04毫米至0.07毫米，可轻松通过标准的1.7毫米打印机喷嘴。A 100 μm nozzle is used with a drop drive frequency of 28,000 drops/second.
一个100微米的喷嘴使用了28,000滴/秒下降的驱动频率。
