淬 - 翻译成英语

• cui
• quenching
• hardening
• quenched
• quench

在 中文 中使用 淬 的示例及其翻译为 英语

当合金被加热时，铜在材料中均匀分布，淬火过程将铜困在这些位置。
When the alloy was heated, the copper spread evenly through the material and the quenching process trapped the copper in these locations.

齿表面也可按照用户的要求淬火处理，淬火硬度在HRC～，并且能够足够的深度。
Tooth surface can also be quenched in accordance with the requirements of the user, quenching hardness HRC50~ 60, and can guarantee sufficient depth.

达到该温度后，设备停止加热，并自动向牙齿表面喷洒淬火液，以完成淬火过程。
After reaching the temperature, the equipment stops heating and sprays quenching liquid automatically to the tooth surface to complete a quenching process.

不要在300-375C回火,会降低工具的韧性，出现回火脆性，另外淬后立即回火。
Do not tempering at 300-375C, will reduce the tool's toughness, temper brittleness, the other tempering immediately after quenching.

Pa的氦，冷却能力等于或略高于油淬，已进入工业实用。
Pa helium, the cooling capacity is equal to or slightly higher than the oil quenching, has entered the industrial practice.

为了使工件表面和内部都获得满意的力学性能，必须采用真空高压气淬技术。
In order to obtain satisfactory mechanical properties both on the surface and inside of the workpiece, the vacuum high-pressure gas quenching technology must be adopted.

冷拔锤头前的加热温度为700～850℃，加热时要防止渗碳，锤头后进行水淬。
The heating temperature before the cold-drawn hammer is 700-850° C. It is necessary to prevent carburization during heating and water quenching after the hammer.

过共析钢的淬火加热温度不能低于AC1，由于此时钢材尚未奥氏体化。
The quenching and heating temperature of hypereutectoid steel can not be lower than AC1 because the steel has not been austenitizing at this time.

ER5钢的推荐热处理工艺：对高耐磨性、高强韧性的模具，采用1150℃淬火，520~530℃回火3次;
ER5 The recommended heat treatment process for steel: the mould for high wear resistance and high toughness 1150℃ quenching The fire, 520~ 530℃ tempering 3 Times;

冯淬女士说，喀麦隆有200多个族裔群体，并有多种形式的习惯法，按统一标准来实施这些法律很难。
Ms. Feng Cui said that, with over 200 ethnic groups in Cameroon and as many forms of customary law, it would be very difficult to enforce such laws uniformly.

这种评估方法非常棘手，主要是因为曲面壳板是由工匠手工锻压和淬火而成，而这些工匠所拥有的技能水平可能不尽相同。
Evaluation is tricky mainly because the curved shell plates are pressed and quenched manually by craftsmen, who may possess different skill levels.

试样水淬.
Cylindrical Sample Water Quenching.

淬气体淬.
Quenching Air.

退火淬高频淬火浸炭火.
Annealing Quenching High frequency quenching Carburized.

数控淬火机床.
CNC Induction Hardening Machine.

恒进感应淬火机床.
Shiyan Hengjin Induction Hardening Machine.

例如：可以用油淬火，减少淬火后的变形和开裂倾向。
For example, oil quenching can be used to reduce the deformation and cracking tendency after quenching.

淬火与退火有什么区别？?
What is the difference between ELD and AOBRD?

淬火与退火有什么区别？?
What is the difference between AOBRD and ELD?

这个过程被称为非光化学淬灭。
This process is called nonphotochemical quenching.