Examples of using 的工作温度 in Chinese and their translations into English
{-}
-
Political
-
Ecclesiastic
-
Programming
钢化玻璃的耐热冲击性能很好，最大的安全工作温度为287.78℃，并能承受204.44℃的温差。
Tempered glass thermal impact performance is very good, the maximum safe working temperature is 287.78℃ and can withstand the 的类型电解质也决定了细胞的工作温度，“熔融”碳酸盐电池运行热，正如名字所暗示的。
The type of electrolyte also dictates a cell's operating temperature-"molten" carbonate cells run hot, just as the name implies.一般镀层的温度限制比紧固件材料要低，因此还需考虑紧固件所处的工作温度要求。
In general, the 灯壳散热的目的是降低LED芯片的工作温度。
The purpose of the cooling of the lamp shell is to reduce the working temperature of the LED chip.在500V下，器件的最高工作温度为+105℃，使用寿命超过3000小时。
At 500 V, the devices feature a maximum operating temperature to +105 °C and useful life of>3,000 hours.以上独特的散热设计方案确保了大功率LED光源在45℃以下的安全工作温度。
The above unique heat dissipation design ensures the safe working temperature of the high power LED light source below 45 °C.目前FOOSN连接器的最高工作温度为200度（除高温特种连接器外），最低温度为-65度。
The current maximum operating temperature of the connector is 200℃(except for high 这里所面临的挑战在于如何确保尾气后处理系统能够在发动机启动后尽快达到并保持高效的工作温度。
The challenge focuses on ensuring that exhaust after-treatment systems reach and maintain an effective working temperature in rapid fashion after starting the engine.但优势将是巨大的：加倍的工作温度将减少产生的热量成本的一半，Forsberg说。
But the advantage would be great: Doubling the operating temperature would cut in half the cost of the heat produced, Forsberg says.汽车中的变速箱油将持续多长时间取决于车辆的工作温度以及您进行的驾驶量。
How long the transmission fluid in your car will last depends on the vehicle's operating temperature and how much driving you do.为了确定太阳电池的功率输出，确定PV组件的预期工作温度是重要的。
In order to determine the power output of the solar cell, it is important to determine the expected operating temperature of the PV module.第二个目标是改善PVT吸收器内部的热传导，以降低PV电池的工作温度并提高转换率和热效率。
The second aim was to improve the heat transfer inside PVT absorbers to decrease the PV cell's operating temperature and increase conversion and thermal efficiency.它通常用于高温炉，其温度超过金属材料加热元件允许的最高工作温度和一些特殊场合。
It is generally used in high-temperature furnaces, where the 因此，此类芯片的制造商建议采用热管理技术将器件的工作温度保持在建议的最大值以下。
Consequently, manufacturers of such chips recommend adopting thermal management techniques to keep the devices' operating temperature below a recommended maximum.因此，人们可能会认为数据中心运营商将采取一些简单的措施将设备的工作温度提高几度，这样可以降低一些成本。
So one might assume data center operators would take advantage of something as simple as raising the equipment operating temperature a few degrees.由于机械强度高，所以它们能承受超过1000℃的工作温度，并在10微米的波长下表现出极好的光学性能。
They have a high mechanical strength, are able to withstand working temperatures in excess of 1000°C and exhibit excellent optical properties at the 10micron wavelength.像Teflon一样，与许多聚合物相比Nafion有相对高的工作温度。
Like Teflon®, Nafion™ has relatively high working temperatures compared to many polymers.制造商宣称传感器的工作温度为-20至+60摄氏度，湿度为0％-100％RH。
The manufacturer declares the sensor to operate at a temperature of -20 to+ 60 degrees Celsius and humidity 0% -100% RH.熔盐技术的工作温度接近大气温度，将燃料和冷却剂结合在一起。
Molten salt technology operates at close to atmospheric temperature and combines the fuel and the coolant.FDM打印机的工作温度大约在100摄氏度左右，这可能会影响热稳定性较差的成分，或改变药物的溶解度等特性。
FDM printers operate at around 100 degrees Celsius, which may affect less thermally stable ingredients or alter properties such as the drug's solubility.
