FLANGES in Chinese translation

['flændʒiz]
['flændʒiz]
法兰
flange
french
france
français

Examples of using Flanges in English and their translations into Chinese

{-}
  • Political category close
  • Ecclesiastic category close
  • Programming category close
YI Flange coupling- Chuangming Transmission Equipments Manufacturing.
YL凸缘联轴器-创明传动设备制造.
Flanged Linear Motion Ball Bearing S>> LMEK□L Series.
直线法兰轴承系列>>lmek□系列.
Flanged IMF/ LMFP.
法兰式LMF标/导.
Gearbox Mounting- Flanged Flangeless Eccentric Pilot.
轮箱方式:法兰连接偏心导向.
Flanged Type Butterfly Valva.
法兰式蝶阀.
Flanged pipe systems need much more space(just think of a pipe rack).
法兰管系统需要更多的空间(只考虑管道架)。
Flanged Linear Motion Ball Bearing S>> LMHC□L Series.
直线法兰轴承系列>>lmhc□系列.
Flanged connection: ANSI B16.5.
法兰连接:ANSIB16.5.
This angle is further­broken up by a flanged planetary gear at 134:1.
这个角度比134:1的法兰行星轮精度更高。
Two parallel flange surfaces enable easy and simple connection, processing and installation.
翼缘两表面相互平行使得连接、加工、安装简便。
Chiba Pine Chemical Flange.
化工法兰承可.
Flange Forgings.
法兰盘锻件.
Cangzhou Shengyuan Flange Pipe Fitting Co Ltd.
盛源管件有限公司法兰盘.
In a newly built factory is customary to minimize flange connections, because only one weld is needed to connect two pieces of pipe.
在新建的工厂里,通常要尽量减少法兰连接,因为连接两根管子只需要一个焊缝。
When the valve is connected to the pipe by flange or thread, the valve should be installed in the closed state;
当阀门法兰或螺纹连接到管道时,阀门应安装在关闭状态;
It is essential to check that none of the substance is trapped between the flange and the plate, or in the threads.
必须查明没有物质留在凸缘和孔板之间或留在螺纹内。
Interface mode, generally>DN50 should choose flange interface,≤DN50 can be freely selected according to user needs.
接口方式,一般>DN50要选择法兰接口,≤DN50则可根据用户需要**选择。
Second, the flange gasket has been replaced by the sealing ring to ensure that the seal faces the matching of the sealing surface.
其次,法兰垫圈已被密封环取代,以确保密封件面对密封表面。
(d) missing or loose bolts or nuts on any flanged connection or blank flange are replaced or tightened;
法兰连接或管口盖板螺栓或螺帽失缺的补上,松动的重新上紧;.
For serrated flange surfaces, the typical roughness is 125-500 microinches, while for non-serrated flange surfaces, the roughness is 125-250 microinches.
对于锯齿状的法兰表面,典型的粗糙度为125-500微英寸,而对于非锯齿状的法兰表面,粗糙度为125-250微英寸。
Results: 41, Time: 0.0299

Top dictionary queries

English - Chinese